zedomax.com &#187; Hack

Looking for a great Christmas gift for your whiz kid? Here’s a great DIY that shows you how to make a solar powered ball robot. Of course, there exactly isn’t a kit for this but all the parts are easily findable so it might actually work better than any other gift you can buy off the shelf.

This technology of using minimal electronics and simple mechanical design is call BEAM robotics.

The Miniball itself was originally invented by Richard Weait of North York, Toronto.The Miniball is a amazing robot – it uses a simple circuit and the robot itself proves to be very capable, rarely getting stuck. The Miniball is mechanically complex and electronically simple. (But don’t worry – the mechanical part is still pretty easy)

In this case, we aren’t going to build the original Miniball, but a smaller, more basic wannabe version. This robot is extremely simple and can take a beginner less than 2 hours to build.

Robot DIY – How to Make a Solar Powered Ball Robot!

Brought to you by: Zedomax.com

Craft DIY – How to Make Hand-Warming Heat Gloves!

max — Sat, 21 Nov 2009 20:10:45 +0000

For those of you trying to beat cold in snow, here’s how to make re-usable hand-warming heat gloves using rice as inserts that can be heated via microwave. I can tell you from growing up in the snow in Korea during winters that hand-warming heat gloves can come in super handy on those short trips outside the house.

Place the gloves in your microwave and heat for a few seconds. Microwaves vary, so experiment with yours to see what amount of time and what power level work best. The gloves should feel warm but not hot to the touch. When you have your hands in them, the heat will be trapped against your palms and feel quite a bit warmer, so heat your gloves a little less than you think you need to.

via craftstylish

Brought to you by: Zedomax.com

Craft DIY – How to Make Hand-Warming Heat Gloves!

Table DIY – How to Make a Table Out of Recycled Wood!

max — Sat, 21 Nov 2009 02:20:44 +0000

Here’s a great way to make a table using recycled wood. When I get a big house, I will certainly make one myself. (and upload me doing so on YouTube)

The results on this table are rather magnificent, I didn’t know you could do that with old wood.

There’s a lot of wood out in the world free for the taking — in dumpsters, back alleys, vacant lots, abandoned buildings, recycling yards, and architectural salvage centers. Most wood, if free from rot, is just as strong, durable, and good to use as new wood, once you sand off the weathering. This table was made from all salvaged wood — both dimensional lumber and plywood, mostly taken from decaying buildings in and around Hale County, Alabama

via bedzine

Brought to you by: Zedomax.com

Table DIY – How to Make a Table Out of Recycled Wood!

USB DIY – How to Make Your Own DIY USB Motion Controller!

max — Fri, 20 Nov 2009 23:56:00 +0000

USB DIY – How to Make Your Own DIY USB Motion Controller!

There’s a slew of great USB motion controllers now on the market you can buy but for those of you hackers and DIYers who enjoy the challenge of making one, go ahead and refer to this site on how to make your own DIY USB motion controller. (Of course, don’t forget we made one couple years back before the days of Wii)

This is the schematics for a PIC USB gamepad that I have built in a steering wheel shell. The code for the firmware was written in PicBasic Pro and it implements a HID USB device with 2 axes and 4 buttons (only 2 buttons connected in the prototype). The device is detected by Windows XP/Vista as a standard USB gamepad and can be used with many games and applications.

via make

Brought to you by: Zedomax.com

iPhone DIY – How to Make a Magnifying Camera Lens and LED Flash!

max — Fri, 20 Nov 2009 18:16:52 +0000

Honestly, you might do better using a real camera (such as a DSLR) for taking photos rather than a smartphone like iPhone but if you must, you can make yourself one of these cool magnifying camera lens along with an LED flash that will let you take close-up, macro shots with ease. Also, don’t forget to adjust your iPhone Lens to focus for macro by hacking it if you are going to use this gizmo.

At first, I just had small metal bezels that I used to hold the lenses up to the camera lens. This was clumsy and upon getting the camera close enough to focus, all of the light was crowded out. These are the problems I intended to solve with this device. This is what I came up with.

iPhone DIY – How to Make a Magnifying Camera Lens and LED Flash!

Brought to you by: Zedomax.com

iPod Nano Hack – How to Make an iPod Nano Projector!

max — Fri, 20 Nov 2009 07:25:45 +0000

Well, I guess there’s many uses for old projectors that can be used to make a bunch of things including a macro DSLR lens plus this iPod Nano projector.

This could be a great way to project your iPod Nano photos/videos onto a white wall for all your family to enjoy, an iPod Nano Projector made with an old slide projector!

Imagine if you took that digital camera that you dropped and broke the lens but it still reads memory cards and does photo slide shows on its little screen. If you take the backlight off the LCD you can project light through it so if you could fit it inside a cheap slide projector, you’d have a wall-sized digital photo frame.

iPod Nano Hack – How to Make an iPod Nano Projector!

Brought to you by: Zedomax.com

Chrome OS DIY – How to Install Google Chrome OS!

max — Fri, 20 Nov 2009 02:09:42 +0000

For those of you who can’t wait until Google comes out with automated installation ISO, you might want to try building one yourself by following these instructions here.

You will need a linux-based computer to generate the images though. (or the compiler equivalent in Windows or Mac)

I will try installing Google Chrome OS on my netbook later this week, perhaps have a DIY post on that soon so…

For now, there’s instructions for burning the Chrome OS images to a USB Flash Drive, harddisk, or a VMware virtual machine. I will have to try the USB flash drive, that might be the most portable way to go.

Although I have been excited with Windows 7 lately, having Google Chrome OS run on my netbook might even be more exciting as I’ve had some speed issues with my Eee PC.

Well, I just wish I could make my netbook run a bit faster without changing in hardware but Google Chrome OS certainly could achieve that and more.

Brought to you by: Zedomax.com

Chrome OS DIY – How to Install Google Chrome OS!

DSLR DIY – How to Make an Intervalometer for Canon or Nikon!

max — Fri, 20 Nov 2009 00:30:54 +0000

Intervalometer can be used in DSLR photography to take time-lapse shots. You can buy one of these Intervalometers off the shelf for anywhere between $60 to $200+ but if you got some programming and soldering skills, you might be interested in learning to make one yourself.

Circuit schematics, code, and whole bunch of images are included in this DIY to help you make the intervalometer for your Canon or Nikon DSLR camera.

This instructable is teaches you how to make an intervalometer that can be used with virtually any camera. It has been tested with Canon and Nikon cameras, but making adapter cables for other cameras is just a matter of figuring out the camera pinout.
It’s also available as a kit so you might want to go that route if you are not familiar with programming an AVR.

This intervalometer has the following features:

Intervalometer mode with options to change delay time and exposure time

Sensor mode with built in light sensor and connector for external sensor input

Manual mode allows intervalometer to act like a simple remote cable

Integrated 2×12 LCD display

Fully optically isolated interface to camera

Total package is roughly 1″ x 2.5″ x 3″ finished

Electronics small enough to fit in a mint box

Source code is available for download so that you can change programming as desired

Available as a kit from www.ottercreekdesign.com

DSLR DIY – How to Make an Intervalometer for Canon or Nikon!

Brought to you by: Zedomax.com

DIY Accelerometer Controlled Marble Maze!

max — Thu, 19 Nov 2009 20:20:46 +0000

DIY Accelerometer Controlled Marble Maze!

Here’s a rather very interesting DIY project that involves a marble maze controlled by a wireless accelerometer housed in a Wii Steering Wheel unit. Brilliant!

I purchased the Wii steering wheel unaware that an additional button is mounted to the back for the “B” controller input. At first I considered removing this button to prevent users from getting confused but decided to utilize it instead. During testing I found it awkward and difficult to hand off the controller or put it down without the maze going crazy as it continued to follow the accelerometer’s measurements. I decided that a “dead-mans” switch would be a useful addition so that the maze would only accept input when the button is held down. This allowed the controller to be handled without causing the maze to move unless desired.

via hackedgadgets

Brought to you by: Zedomax.com

Recycle DIY – How to Recycle Tin Cans as Pencil Holders using Grout and Creativity!

max — Thu, 19 Nov 2009 19:53:57 +0000

I really love it when people make things like this out of stuff that would go into your recycling bin, a pencil holder made using old tin cans and grout! Brilliant! Keep up the great work and reduce our carbon footprint!

We all use some canned foods from time to time. And we all probably use empty cans for one purpose or another. This instructable shows how to decorate cans to be used as organizers for pencils, pens, paint brushes, etc. It’s a simple thing to do, and children would especially have fun making their creations.

Recycle DIY – How to Recycle Tin Cans as Pencil Holders using Grout and Creativity!

Brought to you by: Zedomax.com

Earthquake DIY – How to Make a Seismic Earthquake Detector/Reflector!

max — Thu, 19 Nov 2009 01:23:18 +0000

Here’s a rather cool device you can make to let you know when there’s an earthquake anywhere around the world using Arduino and RSS feeds from USGS.gov.

Basically, the device will simulate the intensity of earthquake’s magnitude through vibrations. For seismic scientists and reporters who specialize in earthquakes, this could be pivotal in launching an emergency campaign.

As a Californian who witnessed one of the biggest SF Bay Area earthquakes in 1989 (and lived through it), I can see the value of this gadget. Plus, most big earthquakes hit after a series of small/medium ones, meaning this could potentially alarm people of upcoming earthquake too. I still remember the day when my parent’s house rocked back and forth about 1-2 feet like if I were on a boat or something for full 20 seconds. I didn’t know it was an earthquake at the time until afterwards, that was not a lot of fun as I immigrated to the US like 3 months before it.

Even today, I know there’s another big earthquake coming to San Francisco Bay Area, my prediction is around 2070 though, I think they hit this area every 90 or so years.

This project has two strands, a software and a hardware component. The aim is to build a device which responds to earthquakes being reported in near-real time via the USGS RSS feeds. The device responds by illustrating the magnitude of the reported earthquake via two fairly chunky vibration motors of the kind used in video game controllers. The device is connected to a PC via a virtual com port over USB (thanks to an on board Arduino). On the PC, an application sits there checking the RSS feed periodically and when a new event it posted to the RSS feed, the desktop app parses the data out of it and presents the magnitude of the quake to the Arduino which interpreters this as rate at which to activate the vibration motors.

Earthquake DIY – How to Make a Seismic Earthquake Detector/Reflector!

Brought to you by: Zedomax.com

iMac G4 Hack – DIY iMac G4 Touch Screen!

max — Wed, 18 Nov 2009 08:21:47 +0000

iMac G4 Hack – DIY iMac G4 Touch Screen!

Looking for a cool way to hack your iMac G4 into a touchscreen computer? Look no more, here’s a DIY iMac G4 touchscreen! The author even hacked a Windows 7 into a PowerPC machine, I don’t know how he did that. (I guess you can install Win 7 on PowerPC CPUs??? Will have a post on that soon too then!)

Way cool!

I added the original speakers connected to a Griffin Power Wave Adapter and now I finally have an updated iMac G4 on my desk. It’s connected to a dual booting Windows 7 / Mac OSX Dual Core machine.

via hackedgadgets

Brought to you by: Zedomax.com

Windows 7 Hack – Windows 7 Activation Hacked!

max — Wed, 18 Nov 2009 07:43:21 +0000

This is sorta old news already but I guess Windows 7 activation was hacked within days of Windows 7 official release:

According to Windows enthusiast site Neowin, one of the first to report the crack, a Lenovo disk image of Windows 7 leaked to a Chinese Web site, then moved to English-language domains. Pirates proceeded to retrieve the master OEM key and the OEM activation certificate from the .iso file. Microsoft lets major computer makers like Lenovo, Dell and Hewlett-Packard pre-activate new PCs at the factory to save customers the hassle, and provides OEM master keys for that purpose.

Windows 7 uses an updated activation scheme, dubbed OEM Activation 2.1, which is an updated version of the activation software that first appeared in Windows Vista. The technology, ironically, has been the focus of a Microsoft lawsuit filed last January against a former employee charged with stealing company documents related to the anti-piracy software that computer makers use to lock Windows to their PCs.

My advice? You probably will want to get the official version because a lot of those hacked Windows 7 versions might potentially come with a Trojan horse.

Brought to you by: Zedomax.com

Windows 7 Hack – Windows 7 Activation Hacked!

DSLR Hack – How to Make a Macro Tilt Lens for your DSLR using Lens from a Slide Projector!

max — Wed, 18 Nov 2009 03:35:12 +0000

Need a cheap macro lens for your DSLR? You might want to consider hacking one up yourself from an old slide projector and make this cool, cheap macro tilt lens. It won’t make you look more professional but heck, if you can take better photos, who cares right? See more DSLR hacks here.

I just came back from the Christchurch SuperShed (our city council recycling centre) where I bought a discarded slide projector for $6. In less than an hour, I turned the projector lens into a tilt macro lens for my dSLR. I know there have been lots of these sorts of projects but I tried to do this one without hot glue or gaffer tape so hopefully my process will help you to turn your odd lenses into useable ones.

DSLR Hack – How to Make a Macro Tilt Lens for your DSLR using Lens from a Slide Projector!

Brought to you by: Zedomax.com

RFID Hack – How to Make an RFID Music Selector!

max — Wed, 18 Nov 2009 02:00:59 +0000

For RFID modders, here’s a great DIY to refer to, an RFID application that involves selecting your favorite music using RFID modules! I know some of you are working on RFID projects, this one should be very helpful indeed.

The RFiDJ project is my first attempt at an application in Imperceptible Computing. After work I like to listen to music/radio for a bit to unwind. This usually involves logging into my HTPC and selecting a playlist. For this project I attempted to change how I interact with my music and HTPC. Using RFID tags and photo frame coasters I am attempting to simplify the interface to my music.

via hackedgadgets

Brought to you by: Zedomax.com

RFID Hack – How to Make an RFID Music Selector!

Re-use DIY – How to Make Recycled Wallpaper!

max — Wed, 18 Nov 2009 00:56:52 +0000

I remember when I lived in South Korea for a year couple years back, there used to be a bunch of bars where the walls were pasted with DIY newspaper wallpapers. Of course, they looks sorta nicer, it wasn’t just pasted randomly but looks “clean”.

I think this is a great way to make any room in your home “vintage”. Even better, you might be able to make a wallpaper out of all your old photos somehow, that would be more awesome than your digital frame that’s pushing out only 1 image per second.

you can make wallpaper out of anything from newspapers and magazines to color copies by applying them to the wall with polyurethane (one coat underneath and one on top to seal the paper).

via apartmenttherapy

Brought to you by: Zedomax.com

Re-use DIY – How to Make Recycled Wallpaper!

Sonar DIY – How to Make Sonar-Like Radar Visualizer for an Ultrasonic Scanner!

max — Tue, 17 Nov 2009 22:52:13 +0000

Good morning! Here’s a rather interesting DIY that shows you how to make a sonar-like radar visualizer for an ultrasonic scanner. Now, I think this could easily be applied to other types of scanners including infrared, radio, etc…etc… Great!

First things first, we need to build our circuit. This is the easy bit! We’ll be using the Arduino to control a servo that will rotate our sensor around 180 degrees. The Arduino will then send the value from the sensor along with the current angle of the servo to the serial port.

via make

Brought to you by: Zedomax.com

Sonar DIY – How to Make Sonar-Like Radar Visualizer for an Ultrasonic Scanner!

LED Hack – How to Make a Remote-Controlled RGB LED Mood Light!

max — Tue, 17 Nov 2009 19:34:41 +0000

Like LED hacking? Here’s another rather interesting LED hack involving a remote-controlled RGB LED mood light. Awesome!

With this thing I can control the colour of a bright light into many different colours using the three fundamentals colours : red green and blue. Adding them toghether with different intensity can yeld very great a range of colours from the visible spectrum.

Also check out our Top 30 LED DIY projects here.

LED Hack – How to Make a Remote-Controlled RGB LED Mood Light!

Brought to you by: Zedomax.com

Radar/Laser Detector DIY – How to Make a LIDAR Gun Simulator!

max — Mon, 16 Nov 2009 23:29:24 +0000

With advances in radar/laser detectors that can detect cops from miles away, police officers have been using radar/laser guns that are more sophisticated so they cannot be detected with some of the older radar/laser detectors.

By learning how to make a LIDAR gun simulator, you will be able to actually test whether your current radar/laser detector can detect them all, perhaps saving you some money in the future from getting tickets.

Of course, my advice is just to drive slow enough that you don’t get tickets. In my experience, cops don’t give you a ticket unless you are going at least 15MPH above speed limit and perhaps driving a bit crazy such as weaving in and out of lanes or cutting off other innocent drivers for no reason.

Also, don’t forget you can get PhantomAlert, which is a software add-on for your GPS and lets you know where the cops are.

Brought to you by: Zedomax.com

Radar/Laser Detector DIY – How to Make a LIDAR Gun Simulator!

DROID Hack – How to Tether Motorola Droid and Other Android Phones!

max — Mon, 16 Nov 2009 20:42:58 +0000

Here’s a simple way to tether your motorola Droid using a free app (and there’s a paid app too).

And of course, it seems that this tethering app is only supported for USB or bluetooth, I wish they were able to turn it into a WiFi router like a Palm Pre can. Oh well…

What you’ll need:

USB Driver – Download or Download (Mirror)

Tethering Software – [PDANet] Download (Full version costs $29, onetime)

via taranfx

Brought to you by: Zedomax.com

DROID Hack – How to Tether Motorola Droid and Other Android Phones!

Rocket DIY – How to Make a Water Rocket!

max — Mon, 16 Nov 2009 20:07:10 +0000

Rather than polluting our mother earth with traditional hobby rocket fuel, here’s a great way to experiment and learn about rockets by building water rockets where the fuel is solely based on pressurized air pushing out water. (Of course, don’t forget water can also cut through heavy metal too.)

This instructable with show you how to build water rockets, recovery systems, rocket launchers, two stage rockets and much more.
Water rockets are fun to build and make, but can be dangorous if used improperely.

Rocket DIY – How to Make a Water Rocket!

Brought to you by: Zedomax.com

Windows 7 DIY – How to Run 1680×1050 in Windows 7!

max — Mon, 16 Nov 2009 08:50:20 +0000

To run 1680×1050 resolution (which is typical of 20″ and 22″ LCDs) on your Windows 7, you will need to connect your LCD via an HDMI/DVI cable.

If your computer has HDMI output, you can get this HDMI to DVI cable. If your computer has DVI output, then simply connect DVI to your LCD. (you can get DVI to DVI cable here if you don’t have one)

Windows 7 doesn’t support 1680×1050 without a digital connection, meaning a VGA connection won’t get you the native resolution of your LCD even if you install the drivers. (This is only in Windows 7, XP and Vista supports it on analog too.)

If you don’t have HDMI/DVI outputs on your computer, get an aftermarket graphic card such as Nvidia GeForce 9800. (that is the only way if you want to run Windows 7)

Of course, your LCD monitor must have either a HDMI or DVI input, most have DVI so…

Once you got those digital connections going, you should see an option in Windows 7 to be able to set the screen resolution to the monitor’s native resolution. Yey, problem solved!

Brought to you by: Zedomax.com

Windows 7 DIY – How to Run 1680×1050 in Windows 7!

Xbox 360 Hack – How to “Unban” your Xbox 360!

max — Sun, 15 Nov 2009 19:48:52 +0000

Here’s some great news for Xbox 360 hackers who have been “banned” from modding your Xbox. Sorta complex but I guess it’s doable to unban your Xbox 360.

The new workaround, dubbed iXtreme LT (Light Touch) aims to provide a minimum amount of security checks and aims to make the firmware as close to the stock firmware as possible to prevent detection. This fix may allow modified consoles to return to playing backup discs and other forbidden materials without Microsoft noticing.

via gadgetvenue

Brought to you by: Zedomax.com

Xbox 360 Hack – How to “Unban” your Xbox 360!

Lawn DIY – How to Make an RC Lawnmower!

max — Sun, 15 Nov 2009 18:46:59 +0000

Lawn DIY – How to Make an RC Lawnmower!

Here’s a rather interesting hack that involves a regular lawnmower converted into an RC lawnmower. Brilliant!

This should make lawnmowing much more fun. Better yet, your kids will have a blast cutting the lawn.

This instructable will show you how to make your Arduino into an R/C interface that you can use for just about anything requiring remote control. I will also show you how I built an R/C lawnmower using my Arduino, a cheap R/C transmitter and receiver pair, and a couple of electric-wheelchair motors from Ebay. I have used this interface to control anything from basic LED’s to Bipolar stepper motors, mini-robots, lifeless R/C cars from the thrift store, and even a 100lb lawnmower (all with appropriate motor controllers). It is very flexible and easy to change and very simple to set up.

via hackaday

Brought to you by: Zedomax.com

Hard Disk Life and How to Maximize Hard Disk Life!

max — Sun, 15 Nov 2009 12:03:24 +0000

I’ve always wondered how long a hard disk’s life is if you left it on 24 hours a day (which I do with some of my server computers).

Well on average, according to this site,

The average service life of a hard disk is usually given as “5 years or 20,000 hours.” This means if a hard disk operates 24 hours a day, you will need to replace your drive with a new one every 1.5 to 2 years. (For specification details, refer to your hard disk drive’s user manual.)
The measure of service life used by most hard disk manufacturers is “mean time between failures” (MTBF)*1 (usually quoted at between 300,000 to 500,000 hours). The ratings (for expected service life) used by PC makers are more conservative, as they are based more closely on “real world” usage conditions. Since expected service life and MTBF figures can differ by hundreds of thousands of hours, we recommend you use the expected service life value. For example, the usual service life of a 2.5 inch drive will be almost 5 years or 20,000 hours, if used at the temperatures specified for your PL. However, if a drive is operated continuously, i.e. 24 hours a day, its service life will be shorter.

Also, there’s a way to put your hard disk under sleep mode on most operating systems, I suggest you to turn that on:

I see no reasons why you should leave your hard disks on if you have left your computer for couple minutes or even hours.

For Windows operating systems, go to ScreenSaver->Power then set “Turn off hard disks” to “After 3 mins” so you save both power and your hard disk life. Also digitgeek.com has a great article on maximizing more life out of your hard drive.

Brought to you by: Zedomax.com

Hard Disk Life and How to Maximize Hard Disk Life!

Balding DIY – How to Stop Balding Naturally!

max — Sun, 15 Nov 2009 09:48:50 +0000

Balding can be one of the most traumatizing experience for men and women, especially if they care for their hair. Of course, as for me, I think it’s perfectly okay to be bald, perhaps you would look more “mature”, not that I am bald anytime soon.

For those of you looking to stop balding, there are remedies such as rogaine or propecia, both of which are not natural but may stop/cure balding.

Most of balding is caused by your genes so if your parents are bald, you would probably go bald someday. My dad is balding slightly, he’s now slightly over 60 so it seems I have another 30 years to go before I reach his point or NOT?

Of course, you may want to seek natural remedies for balding. For that I’ve heard scalp massages (where you massage your head with your fingers and circulate more blood) might help. Also I have heard from my hair stylists while I was in Korea that simply washing your hair and drying it properly often helps too. Too often hair loss can be caused from dirty hair. Like your face, you might want to keep your head clean, isn’t that common sense? For one, don’t go to sleep without taking a shower if you’ve sweated profusely.

I also did some research and there’s even a way to stop hair loss by applying fresh coconut milk on your hair. This seems to make sense but I wouldn’t go further.

Would you put horse shit on your scalp if it proved to stop hair loss? I hope to God no, just be natural, if you are going to be bald, just accept it and perhaps girls would find your shaved head even more manly and attractive. Please don’t spend a dime on hair growth products, although I am sure someone is becoming a millionaire this second due to people who spend money on that. (Instead, donate that money to the homeless society please!)

Of course, last but not least, don’t stress yourself, relax!

Life is too short to worry about your hair (or scalp), if you think that much about your outside appearance, perhaps it’s time for you to work on your inner ones first.

Brought to you by: Zedomax.com

Balding DIY – How to Stop Balding Naturally!

Circuit DIY – How to Make PCB with an EAGLE schematic!

max — Sun, 15 Nov 2009 08:57:59 +0000

Here’s a great tutorial showing you how to make a PCB with an eagle schematic. I am sure most of your PCB experts know how to do this but for those of you dummies who can’t, this is invaluable free lessons.

In this instructable, we’ll make a printed circuit board from that schematic

I guess I should say that we’ll make a PCB DESIGN ; making the physical board is a different task, and there are a lot of tutorials on the net (and even some instructables) on making the board after you have the design.

Circuit DIY – How to Make PCB with an EAGLE schematic!

Brought to you by: Zedomax.com

Stroller DIY – How to Make Stroller Handle for your Toddler!

max — Sat, 14 Nov 2009 00:53:52 +0000

Check out this cool little DIY stroller handle you can make for your toddler so he/she can grab while you push your stroller for “the other” baby.

Btw, everyone has been telling my friend about the Maclaren Stroller recall where it has been apparently cutting toddler’s fingers off. (Recall here)

Attach something to the stroller for your older child to hold onto, so that she feels included and so that you know exactly where she is, without rolling over her little feet. Make a Big Brother/Sister Handle out of something you’ve already got in the house.

via craftzine

Brought to you by: Zedomax.com

Stroller DIY – How to Make Stroller Handle for your Toddler!

Windows XP Hack – How to Downgrade to Windows XP When You Get BSOD(Blue Screen of Death) on Boot-up!

max — Fri, 13 Nov 2009 20:18:33 +0000

Recently, my old Acer Aspire X3200 that I’ve bought couple months back needed to be installed with Windows XP because it had more power and memory than my current HP desktop, which is REALLY OLD! I used to have a Ubuntu on it (because I gave up installing Windows XP before) but I finally figured out how to install Windows.

The problem was mainly because my old Windows XP CD doesn’t include the new SATA harddrive drivers for installation, which the Acer Aspire X3200 comes with.

I found that the Acer Aspire X3200 uses an integrated Nvidia card which includes the display, harddisk drivers, and more. I simply downloaded the NForce drivers. Install the .exe file onto a file folder but don’t install the drivers itself.

You will need your existing Windows XP CD, nLite, and download the Nvidia drivers mentioned above. (Also, you can download Windows SP2 to integrate it into your Windows XP CD if it’s OLD like mine.)

First, open up nLite and locate your Windows XP installation:

For me, it was my CD disk:

Next, nLite will ask you which folder to save all the modifications, just make a new folder and choose that.

nLite will then proceed to copy your existing Windows XP copy, just let it do its job for about 10 minutes.

Once your Windows CD is copied, you will find a bunch of options.

For most, you can choose “Drivers” and “Bootable ISO”, I’ve also added “Service Pack” so I can add SP2 to my old Windows CD disk.

If you click “Next”, you will get prompts to find your Service Pack, simply choose the .exe service pack file you downloaded.

Once that’s installed you will come up to a screen where you can add drivers needed for your computer hardware. For me, I installed all the Nvidia drivers.

Next, you can simply create an image by clicking on “Make ISO”.

My image ended up around 800MB so I simply burned it on a DVD but if you want, you can probably take some stuff out of the CD (by customizing it) and burn it to CD.

Boot up and you should be welcomed!

Also, if you have another problem where your driver is set up to RAID, you might be able to skip all the steps above by simply setting up your harddisk as IDE. (See more here on how to downgrade to Windows XP. – also here

Brought to you by: Zedomax.com

Windows XP Hack – How to Downgrade to Windows XP When You Get BSOD(Blue Screen of Death) on Boot-up!

Palm Pre Hack – How to Mount a Custom Palm Pre Touchstone Mount for your Car!

max — Fri, 13 Nov 2009 04:33:48 +0000

Here’s a rather cool DIY that shows you how to mount a custom Palm Pre Touchstone Mount for your car. I think this goes well with Sprint’s on-board voice directions GPS program although I still prefer GoogleMaps as it seems more accurate.

So you’ve been dying to get a Touchstone and put in in the car. You get one only to find out it doesn’t work in the car! As a former professional car audio installer, I’ve got that problem solved and here’s how.

via palmpre-hacks

Brought to you by: Zedomax.com

Palm Pre Hack – How to Mount a Custom Palm Pre Touchstone Mount for your Car!

GoogleMaps Hack – DIY Exercise Bike uses GoogleMaps as Virtual Map!

max — Fri, 13 Nov 2009 01:08:28 +0000

GoogleMaps Hack – DIY Exercise Bike uses GoogleMaps as Virtual Map!

Here’s a rather cool hack where the hacker uses his bike as a GoogleMaps Virtual Map. Using Vuzix iWear as display device while he’s cycling (around the world) on GoogleMaps, this simple hack shows how far GoogleMaps Street View can be applied for adding a little fun to your next workouts.

It’s still in the works but kudos for what he has done so far! Brilliant hack!

Pragmatically explained, it means that I don’t have to sit in the darkness or stare at my garage door while I’m huffing away. Hopefully once this is done, I’ll be able to spend a few nights a week pedalling away downstairs and work my way across the US or Australia over the course of the year. The irony of this project is, well, while it’s supposed to help me entain myself while using the exercise bike, the project itself has been keeping me from exercising. Oh well.

via hackaday

Brought to you by: Zedomax.com

Bike Hack – How to Make a Bike Trailer!

max — Fri, 13 Nov 2009 00:18:28 +0000

For those of you who want to make your own bike trailer (and save about $200 buying a one), you might want to read up on this cool bike hack that shows you how to make a bike trailer. I think this is a great idea for custom bike modders out there who need to make more use of their bikes, especially if they need to lug around luggage to work on a bike. I think this is highly useful as I did lug my Alto Saxophone on my regular cheapy bike rack for years during middle school and that wasn’t a lot of fun to be commuting 5 miles to school everyday.

I made this trailer out of wood as I am a woodworker. I used metal electrical junction box covers cut in half to make my plates for the wheels. The fenders are made out of the middle of a piece of vinyl gutter that I bought at Lowe’s. A 10′ piece of gutter was only about $7.00 and you score it with a utility knife and then just snap it off. Flexes nice and Krylon fusion paint will stick to it well if you let it dry overnight.

via lifehacker

Brought to you by: Zedomax.com

Bike Hack – How to Make a Bike Trailer!

G1 Hack – How to Install GoogleMaps Navigation on the G1 Phone!

max — Thu, 12 Nov 2009 22:50:22 +0000

Here’s a good hack that will let you install GoogleMaps Navigation on your G1 Phone. I believe the new navigation is only supported with the new Android 2.0 but with this hack, all G1 phone users should still be able to access the new GoogleMaps navigation, yey!

Download here

Make sure you have CyanogenMod 4.2.3.1, by the way.

1) Unzip zip to desktop
2) Run Part 1.bat
3) When prompted to press any key, do so; the phone will reboot
4) When your phone is running again, run Part 2.bat
5) When prompted to press any key, the installation process is done.
6) Make sure GPS is enabled
7) Open Maps and press OK
Press Menu
9) Press Directions
10) Enter an end point
11) Click Go
12) Just under “Show on map”, click Navigate.
13) When prompted to install the voice codec, do so.

via gizmodo

Brought to you by: Zedomax.com

G1 Hack – How to Install GoogleMaps Navigation on the G1 Phone!

HD Hack – How to Render Full 1080P or 720P in Sony Vegas Pro 9 Without Freezing or Large Filesize!

max — Thu, 12 Nov 2009 18:09:44 +0000

While trying to render some of my new videos for upload on YouTube with Sony Vegas Pro 9, I encountered a problem where the rendering process would crawl to a stop after 1% or simply freeze. Well, I found a quick solution around it, that is to render it in MP4 instead of AVI.

This works really well btw, now I can do a 20 minute 1080P video rendering in about 5 minutes.

Use the above screenshot settings and change the frame size to 1920×1024 pixels for 1080P. You can also try the above settings for 720P, which should be pretty good also.

Btw, my first short film with Canon 7D is almost done uploading!

via dvinfo

Brought to you by: Zedomax.com

HD Hack – How to Render Full 1080P or 720P in Sony Vegas Pro 9 Without Freezing or Large Filesize!

Airplane Hack – How to Temporarily Fix an Airplane with Duct Tape!

max — Thu, 12 Nov 2009 01:22:29 +0000

One of my best friends and my college freshmen roommate was a redneck guy from Northern California, he has repeatedly told me that duct tape can fix almost everything including relationships.

Well, I can’t believe it, but this guy’s plane got chewed up like a ball of paper by a Grizzly Bear in Alaska then he flew off back up with some duct tape as temporary fix. WOW, duct tape can save lives, make sure you note this if you own a plane.

The fishy aroma attracted a passing grizzly bear who, clearly frustrated at not being able to see the lovely “noms” it could smell, took the plane apart in an effort to find it. Aircraft fabric is no match for bear claws. The bear also chomped both tyres for good measure, then departed the scene.

Alaskans are a hardy bunch, however – as tough as the aircraft they fly. The pilot radioed for two new tyres, three cases of duct tape and a couple of rolls of cellophane to be flown in so he could repair his craft and get home.

via timeslive

Brought to you by: Zedomax.com

Airplane Hack – How to Temporarily Fix an Airplane with Duct Tape!

Network DIY – How to Make an RJ-45 Ethernet Cable Tester!

max — Wed, 11 Nov 2009 23:14:36 +0000

As a self-claimed network technician, I did a whole 5,000 square foot building with Ethernet Cat-6 cables almost 8 years ago. Well, since then I am glad I never had to use an ethernet cable tester but for those of you looking to save some money on this RJ-45 cable tester, you can make your own.

We are going to make DIY RJ45 Cable tester for incredible cheap.As you know cable testers are really expensive insturments and for people who always works with network it is an essential part.
I will try to help you to build one of them with basic electronic ways.

Network DIY – How to Make an RJ-45 Ethernet Cable Tester!

Brought to you by: Zedomax.com

Home DIY – How to Make Floating Candles!

max — Wed, 11 Nov 2009 08:04:03 +0000

Want to add some creepy, ghost look to your home? Look no further and learn how to make floating candles, these can be great for scaring the heck out of your guests.

Of course, don’t forget you can make them even safer by using electric candles or make an electric candle yourself.

Halloween may be long gone but you can still have spooky fun. Float some candles in the air and create the perfect eerie atmosphere.

Brought to you by: Zedomax.com

Home DIY – How to Make Floating Candles!

Kitchen DIY – How to Clean Your Electric Tea Kettle with Calcium Buildup!

max — Wed, 11 Nov 2009 07:44:11 +0000

Here’s a quick way to clean your electric tea kettle that might have built up with calcium deposits over the years, simply boil it with some vinegar and water!

If you have an electric tea kettle with a bit of calcium build-up on the heating element, don’t fret. Simply boil a mixture of equal parts vinegar and water, then empty. The calcium will flush out along with the vinegar mix, leaving your tea kettle fresh, new and smelling cleaner than ever.

via diylife

Brought to you by: Zedomax.com

Kitchen DIY – How to Clean Your Electric Tea Kettle with Calcium Buildup!

LED Hack – How to Make (Google)Voice Activated LED Signs!

max — Wed, 11 Nov 2009 02:07:48 +0000

LED Hack – How to Make (Google)Voice Activated LED Signs!

Here’s a really cool hack that uses GoogleVoice to translate voice into words and to his LED sign. This should save a lot of time anytime you want to change the message on your LED sign. Brilliant!

I made the LED sign following instructions from this tutorial on Nerdkits.com. The hardware is some LED’s, a nerdkit, a piece of cardboard and a bit of wire that I got from some Cat 5 cable laying around. I cut out the cardboard and printed a grid to help me lay out the LED’s. I think mine were 1 cm apart. The soldering took forever and it was the first real time I did any soldering so it looks kinda crappy. Oh well. It works. The sign itself is powered by a 9 volt battery and receives data from my laptop through the serial port via a USB adapter. All that stuff was included in the Nerdkit when I bought it. The microcontroller is running code from the tutorial I mentioned earlier. One of these days I’m going to make an enclosure for this thing.

via hackedgadgets

Brought to you by: Zedomax.com

Recession Hack – How to Sue and Make Money from Evil Telemarketers!

max — Wed, 11 Nov 2009 01:00:08 +0000

Recession Hack – How to Sue and Make Money from Evil Telemarketers!

Remember I did a blog post on how to shut down telemarketers? Well, I found out there’s actually a way you can “sue” and make money from those evil telemarketers who don’t comply to the U.S. law. (probably won’t work in other countries by the way)

Watch the above video to learn how and believe me, this could be something you could do to make some good money and rob those telemarketers from growing their evil empire.

Also, you can report any numbers to FCC and put yourself on do-not-call registry, which makes it illegal for telemarketers to ever call you again. If they do, record the conversation, phone numbers and SUE them for free money!

Brought to you by: Zedomax.com

iPhone Hack – DIY iPhone Controlled Van!

max — Tue, 10 Nov 2009 23:52:47 +0000

iPhone Hack – DIY iPhone Controlled Van!

Check out the Spirit of Berlin Autonomous iPhone-controlled van! The van itself is controlled via an iPhone and through its WiFi connection to the van. I think this touches upon the future of driving, perhaps moms and dads will be able to take their kids to school without actually driving. Yey!

“Spirit of Berlin” is a project of the Artificial Intelligence Group, directed by Prof. Raul Rojas, at Freie Universitaet Berlin.

This Video shows our autonomous car controlled with an iPhone – powered by Appirion, a spin-off of the AI group.

via declubz

Brought to you by: Zedomax.com

Bag Hack – How to Make a Dance Revolution Recycled Bag!

max — Tue, 10 Nov 2009 19:18:52 +0000

Have a one of these dance revolution pads lying around? Well, you can get a bit creative and make one of these bloody Dance Revolution Recycled Bags! (Did I say bloody? Awesome I meant really…)

I am not a sewing expert but if I were, my girlfriend would get a lot of great recycled handbags like this one.

via bag blog

Brought to you by: Zedomax.com

Bag Hack – How to Make a Dance Revolution Recycled Bag!

Lawn Mower DIY – How to Diagnose/Repair a Lawn Mower!

max — Tue, 10 Nov 2009 09:08:25 +0000

For those of you with a lawn mower, you might want to note this great DIY that shows you how to diagnose/repair a lawn mower and its engine parts. I think this can be a great reference in the future if your lawn mower breaks down for some reason. Of course, don’t forget to check out the solar lawn mower mod and solar lawn mower robot too.

In this instructable I will show you how to repair a lawn mower engine, and how to finally kill those gremlins which have been lurching in its bowels. Of course there is now way I can tell you every single problem that could happen to your engine, so I will tell you the major parts of the engine, and how to repair them. I am not a trained mechanic. What I have learned comes from years of reading, and much trial and error. Hopefully from that I can teach you how to become more of an independent person, and maybe save you a few bucks

Lawn Mower DIY – How to Diagnose/Repair a Lawn Mower!

Brought to you by: Zedomax.com

Multi-Touch DIY – How to Make your Own Multi-Touch Table!

max — Tue, 10 Nov 2009 05:59:00 +0000

Here’s a rather cool DIY interactive Multi-touch display project that you can learn to make also. I like this multi-touch project as the display is actually not LCD but a projected screen on a whiteboard.

This rules as I think projected LCDs are slightly more safer for child use, spills, and whatnot.

Also, don’t forget about Ideum’s 100-inch multi-touch table, how to turn an HD TV into multi-touch table, and more on how to build a multi-touch table using regular LCDs too.

Between the Apple iPhone and Microsoft’s interactive table, multi-touch displays are all the rage. This instructable will show you how to turn your lcd projector into an interactive multi-touch display table using a few cheap components readily available from the hardware store.

Multi-Touch DIY – How to Make your Own Multi-Touch Table!

Brought to you by: Zedomax.com

Medical Device Hack – DIY Cellphone Digital Microscope!

max — Tue, 10 Nov 2009 01:52:40 +0000

Here’s an awesome hack involving a cellphone and a microscope! An engineer has made a DIY cellphone digital microscope that can actually be pretty darn useful. I think this hits the sweet spot that perhaps, many of our smartphones can be recycled as devices such as these. Kudos!

Now an engineer, using software that he developed and about $10 worth of off-the-shelf hardware, has adapted cellphones to substitute for microscopes.

“We convert cellphones into devices that diagnose diseases,” said Aydogan Ozcan, an assistant professor of electrical engineering and member of the California NanoSystems Institute at the University of California, Los Angeles, who created the devices. He has formed a company, Microskia, to commercialize the technology.

via nytimes

Brought to you by: Zedomax.com

Medical Device Hack – DIY Cellphone Digital Microscope!

DIY Carpet Light for Awesome Ground Lighting!

max — Mon, 09 Nov 2009 23:47:20 +0000

Here’s a great design for carpet lighting using one of those string lights and carpet material.

Here’s a rather interesting idea that involves lighting and carpets, a DIY spiral carpet light! I think there’s many uses to this concept if applied to carpets in real houses. For example, you can hook it up to a motion sensor so the carpet near your front door will light up whenever you walk in/out of the house. Brilliant!

via bed blog

Brought to you by: Zedomax.com

DIY Carpet Light for Awesome Ground Lighting!

Golf DIY – How to Make Kid’s Golf Clubs!

max — Mon, 09 Nov 2009 22:40:19 +0000

Over the weekend, I had the pleasure of making couple kid’s clubs, all custom-fitted to fit one of my friend’s daughters. You see, the golfing world still doesn’t make enough different sizes for golfers under 5 years of age. Meaning the only way to get your kids to play golf early in life is to cut existing clubs or make them yourself.

Well, I’ve documented the process while I was making these super-short golf clubs detailing how to cut the golf shaft, put the ferrule on, install the clubhead, and also install the golf grip.

This is a great skill to learn and it doesn’t take long to make a golf club. Plus, you will save a bunch of money the next time you need a new club or your children need golf clubs.

I did the 7-iron for about $20 and the driver for about $30, still beats buying them off golf retail stores.

Read the full step-by-step instructions on how to make kid’s golf clubs here.

Whether your toddler is a 12 month year old who’s 1.5 feet tall or a 3 year old 2.5 feet tall, making custom-fit golf clubs can dramatically improve chances of your child playing better golf.

The problem is that most of toddler/junior golf clubs bought off the rack at the retail stores or online are too long for these young, aspiring golfers.

If you want your child to be as good as Tiger Woods or to simply enjoy golf at an early age, it’s vital that you either cut junior golf clubs to fit their height or make toddler golf clubs from scratch as I am showing you in this blog post.

Video Part I – Cutting the Golf Shaft:

Video Part II – Installing Ferrule/Clubhead:

Video Part III – Cutting the Golf Grip:

Video of Whole Thing Making the Wood Driver: